Motorized feeder modules for the manual ...

If you want to learn more, please visit our website.

SMT Caddy is primarily suited for taped and reeled components. Infrequent and odd-shaped components are managed through manual presentation on the provided small tray. Taped (cut tape for small quantities and reeled for larger volumes) are by far the most common supply method for electronic components.

SMT Caddy provides two feeder banks, each capable of accepting up to 10 individual and modular feeders if configured for 8mm width tape. Wider feeder configurations reduce the number of maximum, concurrent feeders. A 4mm feeder bank pitch allows for dense population of feeder modules in the bank, independent of the feeder width configuration.

Each feeder module is supplied as a kit, with the necessary components to configure the feeder in 8, 12, or 16 mm wide tape formats. The rails, take-up spool, and supply reel widths can be configured in any of the three tape widths. No tools are necessary to reconfigure the feeders. A feeder can be set up with new tape within about a minute.

These subminiature feeders are motorized and manually activated. Depressing the button on the feeder (via the pick stylus) advances the tape forward and automatically peels the protective cover tape. The cover tape is spooled on a small bobbin. The component tape is advanced through spooling the cover tape.

KF-SMT supply professional and honest service.

 A feeder module is simply plugged into any location in the bank, automatically making electrical contacts for the motor.

Generally, paper tapes are not to be spooled (customarily used for passive components). Paper tapes are quite rigid and do not spool well on small reels. A cut section of tape (virtually, any length of interest) is loaded into the feeder.

Plastic tapes are much more flexible and can be spooled onto the provided reels (100mm OD, 40mm ID). The reel is loaded over an idler hub with a light, built-in friction mechanism to avoid unwanted tape unspooling through flex memory of the tape material.

Feeder changeover and setup can be performed in about a minute.

About the SMT Pick and Place Machine

• Board Size:
  • L Size: 410x360mm
  • L-Wide Size: 510x360mm
  • XL Size: 610×560mm
• Component Specs:
  • Component Height: 6mm
  • Component Size: Laser Recognition: mm( inch)&#;&#;33.5mm
• Feeder Inputs: Max.240 in case of 8mm tape (on a Electric double tape feeder)
• Placement Specs
  • Placement Speed (chip):
    • 0.040Sec./chip(90,000CPH)
    • IPC: 66,000CPH
  • Placement Accuracy: Laser Recognition: ±0.05mm(±3σ)

Developed under JUKI's "3E EVOLUTION" concept, the ever evolving FX series SMT pick and place machine has been redesigned for ease of use, efficiency, cost effectiveness and increased expandability and compatibility. Using new, highly efficient linear servomotors, lightening and stiffening the head unit, and reviewing the placement sequence allow for an effective tact of 0.040 s/chip (90,000 CPH) (optimum conditions).

From the pioneer of the modular assembly line comes the latest technology in high volume production at the lowest cost of ownership. Offering an interchangeable electronic and mechanical feeder solution combined with a new 22&#; x 32&#; maximum board size, the continuously evolving FX-3RA offers the utmost in flexibility, reliability, and ease of use for both high speed and high mix manufacturing environments.

• Four Gantry; 1 Head Per Gantry - Two Stations - 4Beams - 4Head Configuration
• 6 Nozzles per Gantry - A total of 24 nozzles
• High Accuracy Laser Align Component Centering - On-the-fly Simultaneous Centering using 6-nozzle Multi-laser Head
• Quick Change Feeder Trolleys - Compatible with mechanical and electronic feeders.
• X-Y Linear Servomotors - New linear servomotors and full closed-loop control
• Electronic Feeder Compatible - Using electronic double tape feeders enables mounting a max of 240 component types.

SMT Pick and Place Machine's Chip placement speed is greatly improved

Simultaneous picking and on-the-fly parallel recognition with six nozzles are achieved by using the high resolution LNC60 laser sensor.

A SMT Pick and Place Machine with Unrivaled placement range from ( metric) to 33.5mm square components

The LNC60 brings a new concept in laser centering to the market. This sensor has the unique ability to center components from ( metric) to 33.5mm square parts. From ultra-small, ultra-thin, chip-shaped parts to small QFP, CSP, BGA, a wide range of parts can be mounted by the laser recognition system at high-speed and with high-accuracy.

This SMT Pick and Place Machine Supports a Wide Range of Components

FX-3RA can widely recognize and place angular parts ranging from ( metric) to 33.5mm square. By combining it with a High-speed Flexible Placement System KE or KEV, placement parts are effectively sorted supporting highly flexible production capability.

For more information, please visit Siemens Smt Feeder.