Basic Knowledge of Mud Pumps VDO Training‎

For more information, please visit HRSB.

Post Views:

14,957

Mud pump is one of the most critical equipment on the rig; therefore personnel on the rig must have good understanding about it. We&#;ve tried to find the good training about it but it is very difficult to find until we&#;ve seen this VDO training and it is a fantastic VDO training about the basic of mud pumps used in the oilfield. Total length of this VDO is about thirteen minutes and it is worth to watch it. You will learn about it so quickly. Additionally, we also add the full detailed transcripts which will acceleate the learning curve of learners.

Please feel free to share with anyone : )

Transcript for this VDO for learning purposes

Powerful mud pumps pick up mud from the suction tank and circulate the mud down hole, out the bit and back to the surface. Although rigs usually have two mud pumps and sometimes three or four, normally they use only one at a time. The others are mainly used as backup just in case one fails. Sometimes however the rig crew may compound the pumps, that is, they may use three or four pumps at the same time to move large volumes of mud when required.

Rigs use one of two types of mud pumps, Triplex pumps or Duplex pumps. Triplex pumps have three pistons that move back-and-forth in liners. Duplex pumps have two pistons move back and forth in liners.

Triplex pumps have many advantages they weight 30% less than a duplex of equal horsepower or kilowatts. The lighter weight parts are easier to handle and therefore easier to maintain. The other advantages include;

&#; They cost less to operate

&#; They are fluid end is more accessible and

&#; They discharge mud more smoothly. That is, the triplex&#;s output does not surge as much as a duplex.

&#; One of the more important advantages of triplex over duplex pumps, is that they can move large volumes of mud at the higher pressure is required for modern deep hole drilling.

Triplex pumps are gradually phasing out duplex units. In a triplex pump, the pistons discharge mud only when they move forward in the liner. Then, when they moved back they draw in mud on the same side of the piston. Because of this, they are also called &#;single acting.&#; Single acting triplex pumps, pump mud at a relatively high speeds. Input horsepower ranges from 220 to or 164 to kW. Large pumps can pump over gallons per minute, over L per minute. Some big pumps have a maximum rated pressure of over psi over 50,000 kPa with 5 inch/127 mm liners.

Here is a schematic of a triplex pump. It has three pistons each moving in its own liner. It also has three intake valves and three discharge valves. It also has a pulsation dampener in the discharge line.

Look at the piston at left, it has just completed pushing mud out of the liner through the open discharge valve. The piston is at its maximum point of forward travel. The other two pistons are at other positions in their travel and are also pumping mud. But for now, concentrate on the left one to understand how the pump works. The left piston has completed its backstroke drawing in mud through the open intake valve. As the piston moved back it instead of the intake valve off its seat and drew mud in. A strong spring holds the discharge above closed. The left piston has moved forward pushing mud through the now open discharge valve. A strong spring holds the intake valve closed. They left piston has completed its forward stroke they form the length of the liner completely discharging the mud from it. All three pistons work together to keep a continuous flow of mud coming into and out of the pump.

Crewmembers can change the liners and pistons. Not only can they replace worn out ones, they can also install different sizes. Generally they use large liners and pistons when the pump needs to move large volumes of mud at relatively low pressure. They use a small liners and pistons when the pump needs to move smaller volumes of mud at a relatively high pressure.

The company is the world’s best Mud Pumps for Drilling Rigs supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.

In a duplex pump, pistons discharge mud on one side of the piston and at the same time, take in mud on the other side. Notice the top piston and the liner. As the piston moves forward, it discharges mud on one side as it draws in mud on the other then as it moves back, it discharges mud on the other side and draws in mud on the side it at had earlier discharge it. Duplex pumps are therefore double acting.

Double acting pumps move more mud on a single stroke than a triplex. However, because of they are double acting they have a seal around the piston rod. This seal keeps them from moving as fast as a triplex. Input horsepower ranges from 190 to hp or from 142 to kW. The largest pumps maximum rated working pressure is about psi, almost 35,000 kPa with 6 inch/152 mm linings.

A mud pump has a fluid end, our end and intake and the discharge valves. The fluid end of the pump contains the pistons with liners which take in or discharge the fluid or mud. The pump pistons draw in mud through the intake valves and push mud out through the discharge valves.

The power end houses the large crankshaft and gear assembly that moves the piston assemblies on the fluid end. Pumps are powered by a pump motor. Large modern diesel/electric rigs use powerful electric motors to drive the pump. Mechanical rigs use chain drives or power bands (belts) from the rig&#;s engines and compounds to drive the pump.

A pulsation dampener connected to the pump&#;s discharge line smooths out surges created by the pistons as they discharge mud. This is a standard bladder type dampener. The bladder and the dampener body, separates pressurized nitrogen gas above from mud below. The bladder is made from synthetic rubber and is flexible. When mud discharge pressure presses against the bottom of the bladder, nitrogen pressure above the bladder resists it. This resistance smoothes out the surges of mud leaving the pump.

Here is the latest type of pulsation dampener, it does not have a bladder. It is a sphere about 4 feet or 1.2 m in diameter. It is built into the mud pump&#;s discharge line. The large chamber is form of mud. It has no moving parts so it does not need maintenance. The mud in the large volume sphere, absorbs this surges of mud leaving the pump.

A suction dampener smooths out the flow of mud entering into the pump. Crewmembers mount it on the triplex mud pump&#;s suction line. Inside the steel chamber is a air charged rubber bladder or diaphragm. The crew charges of the bladder about 10 to 15 psi/50 to 100 kPa. The suction dampener absorbs surges in the mud pump&#;s suction line caused by the fast-moving pump pistons. The pistons, constantly starts and stops the mud&#;s flow through the pump. At the other end of the charging line a suction pumps sends a smooth flow of mud to the pump&#;s intake. When the smooth flow meets the surging flow, the impact is absorbed by the dampener.

Workers always install a discharge pressure relief valve. They install it on the pump&#;s discharge side in or near the discharge line. If for some reason too much pressure builds up in the discharge line, perhaps the drill bit or annulus gets plugged, the relief valve opens. That opened above protects the mud pump and system damage from over pressure.

Some rig owners install a suction line relief valve. They install it on top of the suction line near the suction dampener. They mount it on top so that it won&#;t clog up with mud when the system is shut down. A suction relief valve protects the charging pump and the suction line dampener. A suction relief valve usually has a 2 inch or 50 mm seat opening. The installer normally adjusts it to 70 psi or 500 kPa relieving pressure. If both the suction and the discharged valves failed on the same side of the pump, high back flow or a pressure surge would occur. The high backflow could damage the charging pump or the suction line dampener. The discharge line is a high-pressure line through which the pump moves mud. From the discharge line, the mud goes through the stand pipe and rotary hose to the drill string equipment.

Related article: Basic Understanding About Positive Displacement Mud Pumps in Drilling Industry

MUD PUMPS CONFIGURATIONS AND DESIGNS

Mud pumps are akin to the heart, they are key equipment in oil and gas drilling that pumps and circulates the drilling mud. As a key player in the manufacture and sales of oilfield equipment, we have a complete range of triplex mud pumps with compact design, reduced carbon emission, and improved performance.
Our classes of onshore and offshore mud pumps range from 450 to 2,200 hp diesel or electric (AC or DC) powered with to psi ratings. We design our mud pumps to match different rig types, work optimally and safely both onshore and offshore.
 

Features Of the Belt and Chain Transmission Series

This series features robust pumps designed to deliver the highest HSE standards and performance.

&#; Linear Range of between 114 mm to 184 mm (4 ½ -9 ¼ inches).
&#; Stroke range of 305 mm (12 inches).
&#; Maximum pressure of 517 bar (7,500 PSI).
&#; Maximum volume delivery of 771 gpm (2,922 l/min).
&#; Ratings range of 1,194 kW (1,600 hp).
&#; A maximum speed of 120 spm

Features Of the Gear-Driven Series

This series features low noise and low vibrations, high reliability, and a massive 25% reduction in weight.

&#; Linear Range of between 114 mm to 229 mm (4-9 inches).
&#;Stroke range of between 178 mm to 355.5 mm (7 to 14 inches).
&#; Maximum pressure range of between 207 bar to 517 bar (3,000 to 7,500 PSI).
&#; Maximum volume delivery range of between 323 gpm to 1,272 gpm (1,226 to 4,815 l/min).
&#; Rating range of between 336 kW to 1,640 kW (450 to 2,200 hp).
&#; Maximum speed range of between 110 spm to 150 spm.