THE FOUR MAIN MINING METHODS : SCIENCE AND ...

Photo Credit

View Details

There are four main mining methods in a mine operation. The method used will depend on the type of mineral resource that will be mined. Considering its location is it beneath the surface or above the surface, and whether the resource is worth enough money to extract at a profit. Each of the mining methods also has varying magnitude of impact on the surrounding landscape and its environment.

1. UNDERGROUND MINING METHOD
   
   Photo Credit

It is the mineral exploitation in which all the extraction is carried out beneath the surface of the earth. Choice of an underground mining method is closely related to Geology of the deposit and the degree of ground support is necessary to make it productive and safe in all cost.

1. OPEN PIT MINING METHOD
   
   Photo Credit

Open pit mining is a process of digging out rocks or minerals from the earth surface by their elimination from an open pit or borrow. Open-pit mines are characteristically filled until either the mineral resource is all exhausted, or a big ratio of overburden to ore makes more mining non-profitable. When this situation occurs, the exhausted mine operations are at times converted to landfills for disposal of solid wastes. However, some form of controlling water is normally required to keep the mine pit or mine cast from becoming a lake.

1. PLACER MINING
   
   Photo credit

Placers are unconsolidated deposits with detrital material containing valuable minerals. The natural processes of it placer is by which they form range from chemical weathering to stream, water, and wind action. Some of the minerals that are typically recovered by placer mining are gold, tin, platinum, gemstones and diamonds.

1. IN-SITU MINING
   
   Photo Credit

This mining method is also known as solution mining method. This involves leaving the ore where it is in beneath the earth's surface, and the recovering of minerals is by dissolving them and pumping the pregnant solution to the surface where the minerals can be recovered. Therefore, there will be a little surface disturbance and no waste rock will be generated. However, the it need that the ore body is permeable to the liquids used, and the ore must be located so that they do not contaminate groundwater that is near the ore body.

SOURCES:

http://www.world-nuclear.org/information-library/nuclear-fuel-cycle/mining-of-uranium/in-situ-leach-mining-of-uranium.aspx

https://www.britannica.com/technology/mining/Placer-mining

http://www.greatmining.com/open-pit-mining.html

https://www.slideshare.net/tayyabanwar180/underground-mining-methods

If you want to know more check out my other posts all about the mining industry:

THE THREE COMMON MISCONCEPTIONS ABOUT MINING INDUSTRY : SCIENCE

THE ENVIRONMENTAL EFFECTS OF IRRESPONSIBLE MINING INDUSTRY : SCIENCE

A QUICK INFORMATION ABOUT THE 5 STAGES OF MINING : SCIENCE AND EDUCATION

That is all about the four main mining methods. Soon I will discuss each processes and how they are being used.
Please follow and support our very own @surpassinggoogle, @teardrops and also @purepinay. VOTE @steemgigs as your witness!

Mining is the process of obtaining geological materials and valuable materials from the Earth. Materials that are acquired through mining are metals, gemstones, limestone, clay, gravel, and many more that cannot be grown through agricultural processes. These materials cannot be artificially created inside a factory or laboratory, which makes them obtainable through mining only.

There are four main methods of mining through which several different materials are acquired. Here we&#;ll take a look at these four methods and learn how each of them are carried out.

1. Surface mining

Surface mining is a method of mining that involves removing the soil and the overlying rock on top of the mineral deposit. This method of mining gained popularity since the start of the 20th century, especially in North America where the majority of surface mining occurs. Most forms of surface mining use heavy equipment such as earthmovers to remove the overburden before bucket wheel excavators or dragline excavators extract the mineral.

With competitive price and timely delivery, shacman sincerely hope to be your supplier and partner.

Surface mining is done in five ways:

• Strip mining &#;

  Strip mining is the most common surface mining method used to mine coal and lignite. The process is done by removing a strip of overburden before mining a seam of mineral. Strip mining is done only when the ore body is in close proximity to the surface.

• Open-pit mining &#;

  Open-pit mining is the method in which minerals or rocks are extracted from the Earth via an open pit or borrow. 

• Mountaintop removal mining &#;

  Mountaintop removal mining (MTR) is done by mining coal seams underneath mountaintops. The mountaintop is removed by using explosives to break up layers of rock above the seam.

• Dredging &#;

  Dredging is a method of surface mining that uses small dredges to suction up mined material from the bottom of a water body like oceans, lakes, and rivers.

• Highwall mining &#;

  Highwall mining is done to recoup additional coal adjacent to a surface mined area. A continuous miner that&#;s remotely operated creates an entry into the coal seam and from there, the cut coal is transported by conveyors outside.

2. Underground mining

Underground mining is a method of mining that extracts ore from underneath the earth&#;s surface. The entry from the earth&#;s surface to the underground mine may be created via a horizontal or vertical tunnel (also known as adit, shaft, and decline).

Underground mining is used when the ore body is too deep to be profitably mined by open pit, or when the quality of the ore body is high enough to cover up the expenses. Here are some of the most common ways underground mining is done:

• Room and pillar mining &#;

  Tunnels are driven in a chess board-like pattern that are fitted with huge square pillars in between. This method of underground mining is commonly used to acquire coal.

• Narrow vein stopping &#;

  A method of underground mining that is executed in an underground excavation along geological veins, which are crystallised minerals that appear in a distinct, sheet-like pattern. Narrow vein stopping is primarily used to mine platinum.

• Block caving &#;

  The underground version of the open pit mining method where the ore body is undermined and allowed to collapse progressively under its own weight.

3. Placer mining

Placer mining is a method of mining that uses water to recover precious metals from placer or alluvial deposits. Examples of deposits mined by placer mining are gold-bearing sands and gravel that has settled from rapidly moving streams to slower, more stable currents. Placer mining utilises the high density of gold to its advantage, causing it to sink at a much faster from moving water.

Panning is a form of placer mining that uses a pan where large amounts of water and a few handfuls of gold-bearing soil or gravel are placed. The contents of the pan are swirled together, causing the lighter material to be washed over the side and leave the gold and gravel behind. It&#;s one of the most ancient methods of extracting gold, and yet it&#;s still widely practiced today because of its low cost and simplicity.

Since the start of the 20th century, dredging became the most significant method of mining placer deposits, specifically bucket-ladder dredging which uses a continuous chain of rotating buckets around a ladder to scoop the material and deposit it through a barge.

4. In-situ mining

In-situ mining (also called in-situ leaching or recovery) is a mining method that&#;s used to obtain minerals like uranium and copper through drilled boreholes into a deposit. In-situ mining works by dissolving naturally occurring minerals that are in a solid state. A leaching solution is pumped into the boreholes where it makes contact with the ore. The solution gets to work and dissolves the ore before being pumped back into the surface to undergo processing. This method of mining allows for the extraction of salts and metals from an ore body without resorting to conventional mining methods such as underground mining.

There are plenty of advantages to using in-situ mining. It&#;s the most environmentally way to mine ores, and involves minimal to no risk for both the workers and the communities surrounding the site. The reduced noise, dust, and greenhouse gas effects are what make in-situ mining an advantageous mining method, both in terms of its economic and environmental impacts.

The type of mining method used depends on a number of factors such as the type of mineral resource, the location of the minerals, and whether or not it&#;s justifiable to extract the mineral with expensive mining costs. Each mining method has its own advantages and varying levels of environmental impact, all of which are heavily considered prior to mining valuable minerals.

Should you require any further expert advise with regards to mining do not hesitate to get in touch with Oreflow who are a leading mining equipment supplier based in Perth, Western Australia.

The company is the world’s best Mining Industry Solutions supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.